How Often Should You Change Pool Sand Filter

Disclosure: This post may contain affiliate links. This ways that at no toll to you, we may earn a small committee for qualifying purchases.

The sand filter is amongst the iii different filters used in the pool to filter out debris and dirt. The sand filter comes with sand particles inside the filter manifold. These sand particles were graded to trap particles in the range of 20 – 100 micron.

The efficiency of the sand increases with each employ making information technology more capable of trapping more dirt as time goes, but you may need to aftermath the filter yearly to remove all the trapped dirt. Afterwards prolonged use, the filter begins to experience a gradual loss of efficiency for a while and would require a change of sand to get it functioning to its usual standard.

People say the ideal fourth dimension to supersede the sand in your filter should be later five years of use as the gradual loss of efficiency may be hard to detect. You may want to change the sand of your filter, but y'all don't know the quantity of sand to add and the level to stop. You're going to find out if you read further.

Level of the Quantity of Sand to Add together to Puddle Sand Filter

First, the type of sand used in the filter is the # xx-grade silica sand with a 45 – 55 mm quantity. When adding this sand to your filter, put the sand till the filter container is ii/three full to create enough space on top. This way, the sand would have enough infinite to run perfectly.

If the sand is not upwards to that level, your pool water will exist cloudy no matter the number of hours you run your filter, and the pool water volition non exist devoid of droppings. However, you should check with the manufacturer's manual of your filter spec to come across the limit given. But the expected level of sand in your sand pool filter should be two/3 of the filter.

How Oftentimes Should You Replace Sand in Your Pool Filter?

After experimenting with all three types of filters, it is advised that yous change the sand in the pool sand filter between every 3-five years. This time frame works for when your puddle filter functions perfectly.

There are times when the sand may need changing before the stipulated time, and one of such is when the pool water becomes cloudy. This is usually caused past an imbalanced puddle water chemistry, which leaves the pool filled with dirt.

When the pool even so has leftover debris, the filter would work more than its usual time, making the sand filter wear out the sand media and slow down the water circulation procedure leaving the h2o cloudy. At this point, you will demand to change the sand media while likewise practicing puddle treatment methods. Too, check the filter O-band because they're unremarkably the offset to wear out.

How to Change the Sand in a Tagelus Pool Filter?

Do you change the sand in a tagelus filter?

This question has caused a divide amongst public opinions as there take been people who stood for changing the filter sand and people who are against it. Still, the idea of sand replacement is a welcomed one because it is cheaper to change your sand every three to five years rather than trying to make clean the sand with expensive cleaners.

How do you lot change the sand of a tagelus filter?

After determining that the sand in your filter needs changing, you accept to gather the necessary gear and prepare for the following steps.

The post-obit are tools used to change the sand of a tagelus filter.

Screwdriver

Hacksaw

Duct Record

Silica Sand (Check manufacturer'south manual for quantity to add)

Garden Hose

Utility Knife

Shop-Vac

Shut off the pool pump and discharge the filter

The first step to irresolute your filter sand is to put off the puddle pump. Ensure the pump timer is not turned on to end the engine from kicking up while information technology's dry out. Drain out water completely from the tank by removing the drain plug from the tank's bottom.

Detach multiport valve

To remove the multiport valve, yous need to remove the connecting pipes. Cut the pipes off if they're non-detachable. Remove the collar holding the valve with a screwdriver then twist the multiport valve gently to pull it out.

Seal the standpipe

The standpipe is the open up pipage within the tank that connects to the valve. Utilise a duct tape to embrace the pipe so that sand won't enter into the filter. If the sand gets into the filter, it volition exist flushed into the puddle as you lot run the pump.

Remove the sand

To remove the sand from the filter, suck it all out with a Store-Vac. If at that place'south no shop-Vac, scoop out the sand with your cup or bowl, but be conscientious for it non to get into the filter.

Make clean the inside of the laterals and tank

When y'all've finished scooping all the sand, you'll see the terminate of the tank. Rinse the inside of the tank with water to remove all the leftover sand. Audit within the laterals and standpipe for cracks or harm. Any damage or fissure overlooked would cause sand to menstruum into the puddle. Repair whatsoever damage to the standpoint or tank before you lot add new sand.

Add some water halfway into the tank

Put in the bleed plugs and begin to fill the tank with water. Let the tank make full halfway but hold the standpipe and laterals in place. The essence of this water is to stop any falling sand from entering the laterals.

Add new sand

Hold the bag of sand over the tank and open it with any sharp object. Let sand enter the tank upwards till its two/3 filled. Depending on the size of the container, put one purse afterward the other. Don't apply any other sand except that recommended for the pool filter. You can increase the sand's efficiency past adding D.E powder to your new sand.

Add together actress h2o to the tank and aftermath

After calculation the sand, pour water into the tank till it reaches its brim then install the pipes, collar, and multiport valve dorsum to the filter arrangement. Ensure all fittings are held tightly. Adhere the backwash pipe to the filter system and backwash the filter. Let the filter run for a few minutes until the filter glass is clear. Rinse the filter and multiport valve 1 more than fourth dimension.

Set the filter to run

Before running the filter, gear up the valve to filter then plow on the pump.

Conclusion

After putting the new sand and running the pump, notice the filter equally information technology works to make certain everything is working fine until you lot want to change the sand again. Then relax and savour your pool.